WhatsApp / Mob : +86 156 5177 2521
Email : mrwin@cnbangwin.com
Categories
Latest blog
Tags
Air Separation Unit for Liquid Oxygen: 10 Selection Checks
Nov 17 , 2026an air separation unit for liquid oxygen is a cryogenic plant that cools filtered air until it liquefies, separates the oxygen by distillation, and delivers the product as liquid oxygen (LOX) at about -183 °C at atmospheric pressure. The unit turns air into a storable liquid, so you can buffer production, move oxygen by tanker, and fill cylinders on site.
The process rests on one physical fact. Air is roughly 78% nitrogen, 21% oxygen and 0.93% argon by volume. Each gas has a different boiling point. Cryogenic separation exploits that difference instead of a chemical reaction, so the product stays clean.
The entity chain is short and worth memorising, because every specification question hangs off it:
Product:
● liquid oxygen, plus gaseous oxygen, nitrogen and optionally argon.
Function:
● liquefaction by distillation and sub-cooling.
Scenario:
● on-site gas production, merchant liquid supply, cylinder filling, peak shaving.
User:
● gas producers, steel and chemical plants, hospitals with bulk tank farms, fabricators, EPC contractors.
Limits:
● high power demand, long cold start, a fixed economic scale, and strict oxygen-cleanliness rules.
That last line matters. An air separation unit for liquid oxygen is not a plug-in appliance. It is a power-intensive, continuously running asset with a cold box that cannot be switched on and off like a compressor. Buyers who treat it as a commodity purchase usually discover the gap at commissioning.
an air separation unit for liquid oxygen works in four stages. Air is compressed and cleaned, cooled against returning product, and distilled in a column. Oxygen leaves the low-pressure column as a liquid, and a cryogenic pump or an internal compression column raises it to the pressure you need.
The sequence is stable across suppliers, even when equipment details differ.
A main air compressor raises ambient air to process pressure. Downstream, a pre-cooler drops the temperature and knocks out water. A molecular sieve unit then removes water, carbon dioxide and most hydrocarbons. This step protects the cold box. Residual moisture or CO2 will freeze and block the passages, so the switching cycle of the sieve beds is a design point, not an accessory.
The cleaned air travels to the cold box and gives up heat to the returning product streams. Regeneration gas and expansion turbines complete the cooling. A turbo-expander drops pressure and temperature together, which is how the plant reaches cryogenic conditions without an external refrigerant.
Liquefied air enters the high-pressure column, where nitrogen-rich vapour leaves the top. Oxygen-enriched liquid goes to the low-pressure column. There, rising vapour meets falling liquid, and the concentration profile produces product oxygen at the required purity. Argon collects at a side draw if the plant includes an argon column.
Liquid oxygen leaves the column cold and low in pressure. Two routes are common. In one, a cryogenic liquid oxygen pump pressurises the LOX drawn from the cold box, and the product is then reheated in the main heat exchanger before it enters the user's pipeline. In the other, LOX goes straight to a storage tank, and a separate pump or vaporiser serves the point of use. The choice changes your storage size, your battery limit and your start-up behaviour.
choose cryogenic separation when you need high-purity oxygen in liquid form at scale. Choose a PSA oxygen plant or a VPSA plant when you need gaseous oxygen at moderate purity and want a simpler system. Keep buying delivered LOX when your demand is small, seasonal or not yet proven.
|
Criterion |
Cryogenic ASU |
PSA or VPSA plant |
Delivered LOX |
|
Typical oxygen purity |
About 99.5% to 99.6% O2 for standard industrial product |
Roughly 90% to 95% O2, process dependent |
Meets the supplier's spec, commonly 99.5% or better |
|
Liquid product |
Yes, LOX is a primary product |
Generally no; the product is gaseous |
Yes, you buy the liquid |
|
Scale |
Packaged units up to very large single trains |
Small to medium gaseous demand |
Any size, limited by tank and delivery |
|
Capital cost |
Highest |
Moderate |
Lowest |
|
Operating cost |
Low per unit of gas, dominated by power |
Moderate |
Highest per unit of gas, exposed to delivery and rental pricing |
|
Start-up |
Long cold start, needs steady operation |
Minutes to hours |
Immediate |
|
Best fit |
Merchant liquid, cylinder filling, large continuous demand |
Captive gaseous use, lower purity tolerance |
New sites, small or uncertain demand, backup supply |
Two practical notes on choosing an air separation unit for liquid oxygen. First, purity and liquefaction pull in opposite directions on cost, so a plant designed for maximum liquid output differs from one built for pipeline gas. Second, a delivered-LOX contract is not wasted money even if you plan to build. It de-risks the demand curve while the project runs.
fix the duty, the product slate, the battery limit and the guarantee basis. Suppliers can only price what you define, and vague enquiries come back with incomparable numbers.
Use this checklist as your enquiry sheet for an air separation unit for liquid oxygen.
Demand basis.
1. State oxygen in Nm³/h and in tonnes per day. Separate average, peak and minimum. Add the hourly and seasonal profile.
Product slate.
2. Gas only, liquid only, or both. Add nitrogen and argon if you need them.
Purity and pressure.
3. Give the figure at the battery limit, with the tolerance and the analyser basis.
Design ambient conditions.
4. Site temperature extremes, humidity, elevation and air quality all shift capacity and power.
Utilities.
5. Voltage, frequency, transformer capacity, cooling water flow and temperature, instrument air, steam if required.
Plot plan.
6. Available footprint, cold box height, crane access, transport route limits and distance to storage.
Storage and filling.
7. Autonomy in days, tank size, vaporiser duty, pump pressure, cylinder filling or tanker loading.
Codes and documentation.
8. Design codes, certification, hazardous area classification, documentation language and handover format.
Commercial frame.
9. Spare parts list, service scope, commissioning support, performance guarantee and liquidated damages.
Schedule.
10. Site readiness date, cooldown window, performance test date and the acceptance criteria.
If you cannot answer item 1 with real operating data, stop. Every later decision, from compressor selection to storage size, is a guess until the demand profile exists.
buy the purity your process actually needs, and set pressure at the battery limit rather than at the machine. Overspecifying purity raises cost without adding value.
Most industrial users accept standard cryogenic oxygen at about 99.5% to 99.6% O2. Higher purity needs more column stages or an additional purification step, and it consumes more energy per unit. Medical oxygen follows a different route: it must meet the applicable pharmacopoeia, for example the USP oxygen monograph, which sets a minimum of 99.0% O2 plus limits on moisture and other impurities. Confirm the rule with your regulator before you write it into a specification.
Pressure deserves the same discipline on any air separation unit for liquid oxygen. Delivering gas at 3 bar from an internal compression column is a different machine from delivering 30 bar through a downstream booster compressor. Decide where the boundary sits, and state whether the booster compressor belongs in the supplier's scope.
Product mix is the third lever. An air separation unit for liquid oxygen can also export gaseous oxygen, nitrogen and argon, and the split between liquid and gas is a design variable called the liquefaction ratio. Higher liquid output costs more power. If argon recovery is on the table, treat it as a separate business case tied to your local argon price and offtake, not as a free bonus of a bigger plant.
compare specific power at the same purity, pressure and ambient conditions, measured on the same boundary. A single kWh figure without those four qualifiers is not comparable.
On any air separation unit for liquid oxygen, compression dominates operating cost. Suppliers usually quote specific power in kWh per Nm³ of gaseous oxygen, or per tonne of LOX. Both are legitimate, but only inside a defined envelope.
Make the guarantee explicit in the contract:
Basis conditions:
● inlet air temperature, pressure, humidity and elevation used for the rating.
Product conditions:
● oxygen purity, pressure and the liquid-to-gas split.
Boundary:
● which loads count. Main compressor, booster, cooling water pumps, instrument air and cold box auxiliaries must all sit inside or outside the figure consistently.
Test method:
● the measurement code and instrument accuracy used at the performance test.
Remedy:
● what happens if the measured figure misses the guarantee, and how the shortfall is valued.
One more comparison trap: a quote that shows a lower total kW may simply have a smaller machine. Normalise by output. Then check part-load behaviour, because few plants run at 100% all year. Ask for the guaranteed turndown range and the specific power curve across it.
storage sets your resilience, and filling equipment sets your revenue. Both are frequently left out of the first budget, then added later at a premium.
LOX leaves the cold box as a cryogenic liquid that must be kept cold and vented safely. A vacuum-insulated LOX storage tank, a pressure build-up circuit, a vaporiser and a transfer line form the minimum. Size the tank from daily demand multiplied by the autonomy you want. For a plant that must keep supplying through a planned shutdown or a road closure, that number is a decision, not a default.
Filling adds a second layer. Cryogenic pumps raise LOX to cylinder-filling pressure, and a filling manifold with weight or level control doses each cylinder. Cylinders and their valves must be oxygen-clean, correctly rated and within hydrostatic test date. The gas-cylinder manufacturing side of the Bangwin group publishes its cylinder approvals and production range at bangwingascylinder.com, which is a useful reference point when you plan filling capacity.
The mistake to avoid is buying an air separation unit for liquid oxygen without a filling or dispatch plan. Liquid that cannot leave the site becomes boil-off, and boil-off is lost product.
power capacity, cooling, plot space and transport access decide whether the plant fits at all. Check them before you compare prices.
An air separation unit for liquid oxygen is an infrastructure project wearing a machine's clothes. Screen these items early:
Electrical supply.
● Transformer capacity, voltage level, motor starting current and the protection study. Large compressors may need a soft start or a variable-speed drive.
Cooling.
● Water flow, temperature and quality, or air cooling where water is scarce. Cooling capacity affects both capex and the power figure.
Air inlet quality.
● Dust, solvent vapour, coastal salt and nearby flares all matter. Contaminated inlet air reaches the molecular sieve and the cold box.
Layout.
● Cold box height, maintenance access, tank separation distances, tanker turning circle and future expansion room.
Environment.
● Ambient temperature changes capacity and specific power. Hot climates cost output; altitude costs mass flow.
Logistics.
● Oversized vessels and columns must travel from the factory to site. Bridge heights and port access are real constraints.
None of these items is exotic. All of them are cheaper to solve on paper than on site.
apply the oxygen-safety and cryogenic-storage codes of your jurisdiction, plus the pressure-vessel and electrical rules for the site. Oxygen cleanliness is the non-negotiable one.
An air separation unit for liquid oxygen carries two safety themes: oxygen cleanliness and cryogenic containment. Oxygen supports combustion, and LOX concentrates that risk. Common reference points include NFPA 55 for compressed gases and cryogenic fluids, and CGA G-4 for oxygen service cleanliness and materials selection. Pressure vessels and piping follow the applicable design code for the destination, for example the ASME code or the European Pressure Equipment Directive route. Cylinders follow standards such as the ISO 9809 series for seamless steel cylinders, plus the transport rules of the importing country. Hazardous area classification and electrical protection follow local rules.
Confirm every citation against the current edition and your local regulator. Codes change, and national adoption differs. A supplier that cannot name the code edition it designs to is a warning sign.
Documentation is part of the deliverable, not paperwork to argue about later:
● P&IDs and general arrangement drawings, as built.
● Material certificates, non-destructive testing reports and pressure test records.
● Operation and maintenance manuals, plus a troubleshooting guide.
● Cause-and-effect matrix, alarm list and control philosophy.
● FAT and SAT protocols with signed results.
Ask for the document list in the enquiry, and specify the language. Retrofitting translated manuals into a running plant is avoidable friction.
test at the guaranteed point, continuously, with calibrated instruments. Then compare offers on total cost of ownership, not on the purchase price alone.
Accepting an air separation unit for liquid oxygen takes six steps, not one signature. A workable sequence looks like this:
Mechanical completion check.
1. Confirm punch list closure, instrument calibration and safety interlock function.
Cold start and stabilisation.
2. Record cooldown time and the stabilisation period from first liquid to steady state.
Continuous performance run.
3. Hold the guarantee point for an agreed period, commonly 72 hours, and log capacity, purity and power.
Purity verification.
4. Use a calibrated oxygen analyser with a traceable calibration gas, and agree the sampling point in advance.
Turndown and trip tests.
5. Verify the guaranteed minimum load and the behaviour after a power dip or compressor trip.
Documentation handover.
6. Collect as-built drawings, test records and the spares list before the retention payment.
For supplier comparison, score against fixed weights instead of impressions.
|
Evaluation criterion |
What to request |
Why it changes the decision |
|
Specific power at guarantee point |
Value, boundary definition and test method |
Largest lifetime cost driver |
|
Purity and capacity guarantee |
Figures with tolerance and remedy |
Defines usable output |
|
Reference plants |
Similar size, similar climate, contactable |
Shows real operating behaviour |
|
Scope completeness |
Battery limit drawing and excluded items list |
Prevents later variation orders |
|
Spare parts and service |
Critical spares list, response time, engineer availability |
Determines uptime after year one |
|
Documentation and training |
Document list, language, training days |
Determines independence |
|
Schedule credibility |
Milestone plan with cold start and test dates |
Reveals optimistic bids |
unclear battery limits, purity and power compared on different bases, and storage sized by guesswork.
Most failures with an air separation unit for liquid oxygen begin in the specification, not the hardware. The recurring ones are predictable:
Buying on capital cost alone.
1. Power and availability decide the real cost over a plant's life.
Comparing capacity at different purity.
2. A 99.6% plant and a 99.9% plant are not substitutes.
Ignoring design ambient conditions.
3. A rating copied from a temperate reference site will not hold in a hot climate.
Undersizing storage.
4. No buffer means every upstream hiccup reaches the customer.
Vague battery limit.
5. Unclear scope boundaries create the most expensive change orders.
No spares strategy.
6. A cold box waiting for a valve is a plant producing nothing.
Unrealistic schedule.
7. Cold start, performance testing and operator training take calendar time.
Documentation language gap.
8. Operators who cannot read the manual will not run the plant well.
Each of these is a specification problem. None of them is solved by choosing a different equipment brand after the contract is signed.
Nanjing Bangwin Gas Equipment Co., Ltd. designs and manufactures industrial gas separation and liquefaction equipment, including cryogenic air separation units, PSA and VPSA oxygen plants, nitrogen generators and cryogenic storage tanks. Its catalogue splits cryogenic air separation into small and medium-sized units and large air separation equipment, so an enquiry can start from your oxygen and nitrogen duty rather than from a fixed catalogue size.
On the liquid side, the company describes a cold box arrangement in which LOX and LIN are pressurised by cryogenic liquid pumps and reheated in the main heat exchanger before entering the user's pipeline. That is one of the two routes described earlier, and it suits sites that want pressurised gas without a separate downstream booster.
The company's own material states a design service life of more than 25 years for its large air separation units, and energy savings of 10% to 20% against conventional designs. Treat those as company-stated figures, not independently verified performance. Ask for the reference list and the guarantee basis before you rely on them. Its About page also reports more than 400 installed sets across China and exports to markets including the Philippines, Bangladesh, Malaysia, Argentina, Peru, India, Indonesia, Kazakhstan, Pakistan, Iraq, Egypt and several African countries.
Scope items worth confirming directly with the supplier include turnkey installation support, on-site engineer guidance, operator training, spare parts supply and maintenance response. These are the items that decide how the plant behaves in year three, long after the commissioning team has left.
If you are specifying an air separation unit for liquid oxygen, prepare the ten-point enquiry sheet above and send it with your site conditions. Contact BANGWIN with the duty, purity, pressure and storage requirement, and ask for a battery limit drawing with the offer.
Capacity is set by the oxygen output and the liquefaction ratio, so ask for both. As a working conversion, one tonne of LOX is about 750 Nm³ of oxygen gas, derived from the liquid density of roughly 1.14 kg per litre and an expansion ratio near 1:860.
Standard industrial product is about 99.5% to 99.6% O2. Higher grades need extra column stages or a purification step. Medical supply must meet the pharmacopoeia and local regulatory requirements in the destination market.
Yes. The liquid-to-gas split is a design variable, and many plants are specified with a liquid column plus a gaseous export line. The split affects power, storage size and the guarantee figures, so state it in the enquiry.
Only when the local argon market justifies it. Argon recovery adds columns, cold box volume and complexity. Model it as a separate business case with its own offtake and price assumption.
It depends on plant size, site readiness and the utility tie-in date. Rather than accept a single number, request a milestone plan covering mechanical completion, cold start, stabilisation, performance test and handover.
Most cryogenic plants have a guaranteed turndown range above a minimum load. Ask for that range and the specific power curve, because efficiency falls as load drops. A plant that only performs at nameplate is a poor fit for seasonal demand.
Build the demand profile in Nm³/h and tonnes per day. Then compare a cryogenic air separation unit for liquid oxygen against a PSA plant and a delivered-LOX contract on total cost of ownership at that profile.
define the duty, fix purity and pressure at the battery limit, compare specific power on one basis, and size storage from the resilience you need.
Everything else follows. A clear enquiry sheet produces comparable offers. A defined power guarantee produces a defensible operating budget. A complete scope produces fewer change orders. An acceptance test protocol produces a plant you can hold the supplier to.